BBB BCP-05, BCP-06 Manual (2024)

Contents

Functions

: Current Speed
The current speed is always displayed on the upper set when riding.

DS: Trip Distance
The DS function accumulates the distance data from the last RESET operation as long as the bike is being ridden.

ODO: Odometer
The ODO accumulates total distance as long as the bicycle is in motion, the ODO data can be cleared by the RESET operation only.

: Clock

: Auto SCAN

1. Auto-Scanning Display Mode.
   Press the MODE button till the symbol is displayed. The computer will change the j display modes in a loop sequence automatically every 5 seconds.
2. Fixed Display Mode.
   Press the MODE button to turn off the symbol and select a desired display mode; the j computer will stop the auto-scanning display operation.

Automatic Start/Stop

: Low Battery indicator

AS: Average Speed

1. Is calculated from the DS divided by the RT. The average data counted is from the last RESET to current point.
2. Is updated every second when RT is over 4 seconds.

MS: Maximum Speed
It shows the highest speed from the last RESET operation.

RT: Riding Time
Shows the total riding time from the last RESET operation.

MAIN UNIT SETUP

INITIATE THE COMPUTER

(all clear) (Fig. 1)

1. Put the battery into the main unit when purchased.
2. Press the MODE button and SET button simultaneously for more than 3 j k seconds to initiate the computer and clear all data.
   
   Be sure to initiate the computer before it is be used, otherwise the computer may run errors.
3. The LCD segments will be tested automatically after the unit is initiated.
4. Press MODE button to stop LCD test. The flickering "KM/H" appears.

UNIT SELECTION

(Fig. 2)
Press MODE button to choose KM/H or M/H. Then press the SET button to j k store the selection.

WHEEL CIRCUMFERENCE

(Fig. 3)

1. Roll the wheel until the valve stem is at its lowest point close to the ground, then mark this first point on the ground. (Fig. a)
2. Get on the bike and have a helper push you until the valve stem returns to its lowest point. Mark the second point on the ground. (Sitting on the bike achieves a more accurate reading since the weight of the rider slightly changes the wheel circumference).
3. Measure the distance between the marks in milimeters. Enter this value to set the wheel circumference. OPTION: Get the suitable circumference value from the table. (Fig. b)
4. A quick press of the MODE button advances the flickering digit by 1.
5. To change the flickering digit, hold down the MODE button 2 seconds till the j flickering digit moves to the next digit.

CLOCK SETTING

(Fig. 4)

1. Press the SET button to enter the clock adjusting screen to setting the clock.
2. A quick press of the MODE button to select 12HR or 24HR.
3. Adjust the clock data as the data setting proces shows. ( Fig 4. )

ODO DATA SETTING

(Fig. 5)
The function is designed to re-key the former data of ODO when battery is replaced. A new user does not need to set this data. Each press of the SET button skips one k setting data process.

BUTTON AND OPERATIONS

MODE BUTTON

(Fig. 7)

Quickly press this button to move in a loop sequence from one function screen to another.

SET BUTTON

(Fig. 8)

1. Press this button to get in the setting screens when you want to reset the bike computer, or the current time of the CLK .
2. Each press of the SET button skips one setting data process.
3. Press this button 2 seconds to get out the setting.

RESET OPERATION

(Fig. 9)

1. Press the MODE button till the LCD digit is blanked, then release it. The computer j will reset AS, DS, RT and MS data from stored values to zero.
2. It will not reset ODO, CLK .

AUTOMATIC START/STOP

(Fig. 10)
The computer will automatically begin counting data upon riding and stop counting data when riding is stopped. The flickering symbol indicates that the computer is active.

POWER AUTO ON/OFF

To preserve battery, this computer will automatically switch off and just displays the CLK data when it has not been used for about 15 minutes. The power will be turned on automatically by riding the bike or by pressing the button .

LOW BATTERY INDICATOR

1. The symbol "" will appear to indicate the battery power is low.
2. Replace battery with a new one within a few days after the symbol was appeared, otherwise the stored data may be lost when the battery voltage is too low.

BATTERY CHANGE

(Fig.11)

1. All data will be cleared when battery is replaced.
2. The computer allows you to re-key the ODO data after replacing the battery.
3. Remember the ODO data before you remove the old battery.
4. Replace with a new CR2032 battery in the compartment on the back of the computer with the positive (+) pole toward the battery cap. 5. Initiate the main unit again.

PRECAUTIONS

1. This computer can be used in the rain but should not be used under water.
2. Don't leave the main unit exposed to direct sunlight when not riding the bike.
3. Don't disassemble the main unit or it's accessories.
4. Check the position and gap between sensor and magnet periodically.
5. Clean the contacts of the bracket and the bottom of the main unit periodically.
6. Don't use thinner, alcohol or benzine to clean the main unit or its accessories when they become dirty.
7. Remember to pay attention to the road while riding you bicycle.

TROUBLE SHOOTING

Check the following before taking the unit in for repairs.

Functions		Specification
	Current speed	0-199.9km/h 0-120.0m/h +/- 1%
AS	Average speed	0-199.9km/h 0-120.0m/h +/- 1%
MS	Maximum speed	0-199.9km/h 0-120.0m/h +/- 1%
DS	Trip distance	0-999.99km/mile +/- 0.1%
ODO	Odometer	0-999999km/mile +/- 0.1%
RT	Riding time	0H:00M:00S-99H:59M:59S +/- 0.003%
	12/24H clock	1H:00M:00S-12H:59M:59S0H:00M:00S-23H:59M:59S +/- 0.03%

Operation Temperature: 0 C ~ 50 C (32 F ~ 122 F)
Storage Temperature: 10 C ~ 60 C (14 F ~ 140 F)
Main Unit Battery Power: 3V battery x 1 (CR2032), battery operating life is about 1 years. (Based on an average of 1.5 hours use per day)
Dimensions and Weight: Main Unit: 40.7 x 52.3 x 15.2mm/ 27g

*Specifications and designsmay be changed without notice.